Temperature and Humidity Sensor T1
FAQ
Move the Temperature and Humidity Sensor T1 close to the Hub, open the app, tap "Home" and the tap "+" in the top right corner to enter "Add Accessory" page. Select "Temperature and Humidity Sensor T1" and add it according to instructions. When the Hub makes voice prompts, it indicates that it is added successfully.
Possible reasons:
1. Operation error. Please add the accessory according to Add Accessory method again.
2. The accessory is too far away from the Hub. Please move the accessory closer to the Hub.
3. There are more than 32 accessories under this Hub.
Possible reasons:
1. The accessory is too far away from the Hub, please try to install the accessory closer to the Hub.
2. Low battery or dead battery. Please replace the battery.
3. The accessory is installed on the metal surface and the signal is interfered. Please avoid metal surface.
After the Temperature and Humidity Sensor T1 is connected successfully and before it is installed, press the button of the Temperature and Humidity Sensor T1, if the Hub makes a voice prompt "Normal link confirmed", current location is proper; if the Hub doesn't make a voice prompt, move the Temperature and Humidity Sensor T1 closer to the Hub and try again.
1. The distance between the Hub and the Temperature and Humidity Sensor T1 should not be too far. Press the reset button before installation. After the Hub makes a prompt of normal connection, install the sensor;
2. Stick using the attached sticky tape or simply place it at your desired location;
3. Do not place it at a location exposed to rain or vapor if possible;
4. Do not install it in the refrigerator, kitchen or washroom if possible.
1. The sensor is too far away from the Hub, please move it close to the Hub;
2. Run out of battery. Please replace the battery.
If you don't want to use it or you want to add it to other hubs, long press the reset button for over 5 seconds until the indicator light blinks three times. Then the Hub will make a voice prompt "Device Deleted".
Single-click to check the connectivity to the Hub. It will report the temperature and humidity data to the Hub. Long press to add and reset bridged accessories.
The Temperature and Humidity Sensor T1 cannot be connected to the mobile phone directly. Please connect the Hub to the mobile phone, and then connect the Temperature and Humidity Sensor T1 to the Hub.
The Temperature and Humidity Sensor T1 is for indoor use. Normal operating temperature: -20~50℃ (68 - 122℉); humidity: 0~100%, non-condensing environment.
Temperature precision: ±0.3℃ (32.54℉); Humidity precision: ±3%; Atmospheric pressure precision: ±0.12kPa
If the temperature humidity and atmospheric pressure varies a bit only, data will be reported once an hour.
If the temperature variation exceeds 0.5℃ (32.9℉), the humidity variation exceeds 6% and the atmospheric pressure is no less than 25Pa, data will be reported instantly.
When the Temperature and Humidity Sensor T1 detects that current environment is out of the comfort zone, it will push notifications to the mobile phone. This function can be disabled in the app.
The Temperature and Humidity Sensor T1 can work with other Aqara accessories. For example, when the temperature is higher than the set value, the Temperature and Humidity Sensor T1 will work with the Smart Plug to turn on the electric fan; when the humidity is lower than the set value, the Temperature and Humidity Sensor T1 will work with the Smart Plug to turn on the humidifier.
Indoor responsive distance is about 10 m (32.81 ft) (walls are permissible); outdoor responsive distance is about 65 m (213.25 ft).
1. After the Wi-Fi connection is broken, the sensor can still be triggered, and after being triggered, the sensor will execute corresponding function according to the previous setting in the app. For example, if the Hub has entered security mode before the connection is broken, the Hub will sound an alarm once the sensor is triggered;
2. After the connection is broken, control or response cannot be executed via the app, but local basic functions can be performed.
Please ensure that the distance between the Hub and the sensor doesn't exceed 10 m (32.81 ft) (the effective distance). In this case, it is best to install the sensor at a location closer to the Hub.
