무선 리모트 스위치 T1(1구)
제품 개요
제품 사양
FAQ
구매하기 >

무선 리모트 스위치 T1(1구)

무선 리모트 스위치 T1(1구)

무선 리모트 스위치 T1(1구)

FAQ
Aqara无线开关支持单击、双击、长按三种动作,可根据需要选择相应的动作与其他智能设备进行联动控制。
It supports single-click, double-click, and long press. It can control other smart accessories with different actions.
Aqara无线开关既可以粘贴在墙上,也可以放在桌面。由于金属对无线信号有衰弱作用,不建议无线开关安装在金属门上。作为门铃时,可以将无线开关安装在金属门旁的墙壁上。(详细内容请参考说明书安装操作)
The Aqara Wireless Mini Switch can either be attached to the wall or placed on a table. Installation on a metal door is not recommended because metal surfaces affect the signal. When being used as a doorbell, the wireless switch can be installed on the wall next to a metal door. (Please refer to the quick start guide for more details)
由于室内环境各不相同,无线开关与网关间可通讯的最大距离各不一样。中间不超过两堵墙时效果最好。
The indoor environment varies, and maximum signal strength between the Aqara Hub and the Aqara Wireless Mini Switch is different. There should not be more than two walls in between.
可能的原因:
1. 操作错误,请重新根据设备添加方式,重新添加设备;
2. 距离网关过远,将设备移近网关后重新添加设备;
3. 网关超过了子设备负载量。
Possible reasons:
1. Operation error. Please add the accessory according to Add Accessory method again.
2. The accessory is too far away from the Aqara Hub. Please move the accessory closer to the Aqara Hub.
3. There are more than 32 accessories under this Aqara Hub.
可能的原因:
1. 设备与网关距离较远,请验证传感器与网关间的距离,将设备安装在靠近网关的位置;
2. 电池电量低或电池没电,请更换新电池;
3. 设备安装在金属表面,信号受到干扰。请避免安装在金属表面。
Possible reasons:
1. The accessory is too far away from the Hub, please try to install the accessory closer to the Hub.
2. Low battery or dead battery. Please replace the battery.
3. The accessory is installed on the metal surface and the signal is interfered. Please avoid metal surface.
① 单击无线开关的重置按键,网关发出提示音“连接正常”,则表示无线开关与网关通讯正常,转②;如无提示,请将无线开关移近网关后重试,若还是无提示音,则无线开关可能已经被删除或电池已耗尽,请参照子设备添加方法或电池更换方法重新添加子设备或更换新电池;
② 单击/双击/长按无线开关几次,然后进入app中,Aqara无线开关的主页面,如有状态变化,则表明设备工作正常。
① Click the reset button of the Aqara Wireless Mini Switch. If the Aqara Hub makes voice prompts, "Normal link confirmed", it indicates that the Aqara Hub and the Wireless Mini Switch communicates properly. Go to ②; If there is no voice prompt, please move the sensor closer to the Aqara Hub and try again. If there is still no voice prompt, the sensor might be deleted or run out of battery. Please refer to the accessory adding methods to add the accessory or replace the battery.
②Single-click/double-click/long press the Aqara Wireless Mini Switch several times, enter the homepage of the Wireless Mini Switch in app. If the status is changed, it indicates the accessory works properly.
1、长按3秒设备的重置按键,指示灯闪烁3次,恢复出厂设置;
2、在已绑定的传感器重新绑定到另一个网关的情况下需要先重置传感器,才能让传感器与新网关绑定成功。
1. Press the reset button on the accessory for 3 seconds. The indicator will flash 3 times before resetting to factory defaults.
2. If a connected sensor needs to be connected to another Hub, it has to be reset first.

Specifications

모델명

WXKG05LM

제품 크기

86 × 86 × 15.12 mm

무선 통신 프로토콜

Zigbee 3.0

작동 온도

-5°C~50°C

작동 습도

0~95%, 비결로 조건

배터리 수명

약 2년

Specifications

모델명

WXKG05LM

제품 크기

86 × 86 × 15.12 mm

무선 통신 프로토콜

Zigbee 3.0

작동 온도

-5°C~50°C

작동 습도

0~95%, 비결로 조건

배터리 수명

약 2년